GE Profile PT7800SHSS Installation Manual download pdf (Page 6)

MAKE ELECTRICAL CONNECTIONS

WARNING

Switch power off at the service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Place oven on table or platform even with the cutout opening. For a single oven, the platform must

support 200 lbs. (91 kg); and for a double oven, the platform must support 375 lbs. (170 kg). Connect the

flexible conduit to the electrical junction box as shown below*. Position the conduit in such a manner

that it will lie behind the unit in a natural loop when the oven is installed**. You will need to purchase an

appropriate strain relief clamp to complete the connection of the conduit to the junction box.

* Ovens come equipped with a 40” or 54” long conduit. If a longer conduit is desired, there may be one

available for your model. To check availability or order parts, call 1.800.GE.CARES.

** Double Oven with upper microwave oven we recommend install the conduit to side of junction box as

shown in illustration above.

Junction Box

Conduit

Ground

Red

White

Black

Strain Relief Clamp

(not included) Must Be

Used at Junction Box

Place Oven on a

Support to Assist in

Connecting Conduit

Ground

Wire

SLIDE OVEN INTO OPENING

A. Loop (do not tie) a 36” (91 cm) string around the conduit before the oven is slid into place. This will

keep the conduit from falling behind the oven.

B. Lift oven into cabinet cutout

using the oven opening as a

grip. Carefully push against oven

front frame. Do not push against

outside edges.

C. As you slide the oven back, pull

the string so that the conduit

will lie on top of the oven in a

natural loop. For double oven

with upper microwave oven pull

conduit so that it sits above left

side of the lower oven (as view

from the front).

D. When you are sure the conduit

is out of the way, slide the oven

¾ way back into the opening.

Remove the string by pulling on

one end of the loop.

Pull Out

on String

Loop While

Pushing

the Oven Into

the Cabinet

THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION

NOTE: If residence leads are aluminum conductors, see

WARNING in Section 5, Electrical Requirements.

When connecting to a three-conductor branch circuit, if local

codes permit:

A. Connect the oven ground conductor along with the neutral

(white) lead to the branch circuit neutral (white or gray in

color), using a wire nut.

B. Connect the oven red lead to the branch circuit red lead

and the oven black lead to the branch circuit black lead in

accordance with local codes, using wire nuts.

C. Install proper strain relief clamp.

D. Install junction box cover.

FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION

NOTE: If residence leads are aluminum conductors, see WARNING in Section 5, Electrical Requirements.

When connecting to a four-conductor branch circuit, if local codes permit:

A. Free the neutral (white) lead from being restrained to any other

wires. If necessary, cut the neutral (white) lead and then re-strip

it to expose the proper length of conductor.

B. Attach the appliance grounding lead (green or bare copper) in

accordance with local codes.

C. Connect the oven neutral (white) lead to the branch circuit

neutral (white or gray) in accordance with local codes, using a

wire nut.

D. Connect the oven red lead to the branch circuit red lead and the

oven black lead to the branch circuit black lead in ac cor dance

with local codes, using wire nuts.

E. Install proper strain relief clamp.

F. Install junction box cover.

Ground and

neutral wires (white)

Tape or Crimp

Neutral wire

connection

Black

Red

Branch

circuit

Alternate

knockout

Range

conduit

snaps

into box

Junction Box Cover

White

Black

Red

Branch

circuit

Ground

wires

Alternate

knockout

Range

conduit

snaps

into box

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comments to this Manuals

No comments

GE Profile PT7800SHSS Installation Manual Page 6

Comments to this Manuals

Related products and manuals for Unknown GE Profile PT7800SHSS